Question: Does a wood stove pipe have to go straight up?

The pipe should be as straight and short as possible, with sections properly secured. The horizontal portion of the pipe should rise not less than one-quarter inch to the linear foot, to insure a good draft. You should not pass a stove pipe through a combustible wall for a hook-up with a chimney flue.

Can you run stove pipe at an angle?

Why Angle Matters You should never install a completely horizontal stove pipe. Buildup of creosote can also block the stove pipe and cause smoke to back up into the room. A steep enough angle for the pipe will prevent creosote buildup inside the pipe and possibly prevent a house fire.

Can I vent my wood stove horizontally?

Venting is an important component of all stoves. And wood, gas, and pellet stoves have different venting systems. For instance, wood-burning stoves will always be vented through the roof of your house, but pellet-burning stoves can be vented vertically through the roof, or horizontally through the wall to the outdoors.

How many elbows can a wood stove have?

In a stovepipe set up, never use more than two 90o elbows. The chimney will not draw well if you do.

Does wood stove pipe have to go above roof?

3-2-10 Rule Explained Explained, the chimney pipe must be a minimum of three feet above the roof but also two feet taller than anything within ten feet. The portion of the rule stating the pipe needs to be 2 feet above anything within 10 feet is where most people get confused.

Can a chimney go straight up?

A chimney cannot have more than four bends and no bend can be more than 45 degrees (except if you use a 90 degree “T” off the rear of the stove). If you are are going out through a wall then you will be using two 45 degree bends straight away and have two left if you need them.

Can a stove flue be horizontal?

As excessive bends and horizontal runs can accumulate soot with the risk of blockage, the flue pipe should be kept as vertical as possible and the angle of bends should be no more than 45° from the vertical.

Can you run a wood stove pipe through a window?

The stovepipe, also called a chimney connector, is the component that usually connects the chimney to the stove. When placed through a window, it is meant to exhaust the fumes out of the house. These pipes are often present on wood stoves and an improper installation can be a fire hazard.

How far should a wood stove be away from the wall?

36 inches Wood frame walls covered with dry wall are considered combustible. If no wall protection is used, the common radiant-type stove or heater must be spaced out at least 36 inches from the wall.

What is the 3 2 10 chimney rule?

This rule means that your chimneys shortest side needs to be at least 3 feet above the roof penetration, and its top has to be 2 feet higher than any part of the building thats within 10 feet. There a number of reasons behind this rule.

How high should a wood stove chimney be above the roof?

3 feet The chimney must extend at least 3 feet above the highest point where it passes through the roof, and be at least 2 foot higher than any part of the building within a horizontal distance of 10 feet (Figure 2).

What do you put on floor under wood stove?

Concrete backer board, which is a tile underlayment, provides a heat-resistant, rigid foundation. Most sheets are 3 feet wide and 5 feet long, which isnt large enough to provide adequate protection for some stoves. Using two sheets side-by-side covers more space.

Does a chimney flue need to be straight?

Both the Regulations and the Standards recommend that bends in the chimney be avoided, as a straight vertical chimney performs better. If bends are necessary there must be no more than four in the length of the chimney. Most flue and chimney manufacturers provide standard gather and fireplace components.

How far can you run stove pipe horizontal?

Maximum unsupported horizontal length: 1 m (3 feet). Galvanized flue pipes must not be used because the coatings vaporize at high temperatures and release dangerous gases. The pipe should be as straight and short as possible, with sections properly secured.

What kind of pipe do you use for a wood stove?

Single-Wall Is Standard Single-wall stove pipe is used on standard wood stove installations. According to, it should be at least 24-gauge sheet metal or thicker -- the lower the gauge, the thicker the metal.

Can I use cement board as a heat shield?

Hardi cement board is an inexpensive solution that will form the foundation of an effective heat shield for any application.

Join us

Find us at the office

Apollo- Siders street no. 56, 49428 Moroni, Comoros

Give us a ring

Jessamyn Awalt
+48 152 183 376
Mon - Fri, 7:00-20:00

Contact us